Your Location: Home > News > PSGC-110H-10/100/1000Base-T to 1000Base-X PoE PSE+ GbE Media Converter

PSGC-110H-10/100/1000Base-T to 1000Base-X PoE PSE+ GbE Media Converter
2010-01-29


PSGC-110H is designed a 10/100/1000Base-T to 1000Based-SX/LX (SC/LC) GbE media converter, which allows two types of network segments to be connected easily and inexpensively. Complied with IEEE802.3at draft(Max. PoE output: 30W) and backward compatible with IEEE802.3af (Max. PoE output: 15.4W) Power Over Ethernet standard, this AC powered PoE media converter is a Power Sourcing Equipment Plus (PSE+: Means PoE High Power Output Device) which combines data received over a TP link with 57VDC power, providing power to IEEE802.3af or IEEE802.3at powered device (PD) over the existing CAT5 UTP cable. The converter includes a PD signature sensing and power monitoring features. Other features include over-current protection, under-current detection and fault protection input. The LFP (Link Fault Pass-through) allows the media converter to monitor both the fiber and copper RX ports for loss of signal. In case of a loss of RX signal on one media port, the converter will automatically disable the TX signal to the other media port, thus passing through the link fault. FEF (Far End Fault) enables the converter to stop sending link pulse to the link partner once a loss of the fiber RX signal is encountered. Then the link partner will synchronously stop sending data. FEF prevents loss of valuable data transmitted over invalid link. Combining LFP and FEF troubleshooting features of PSGC-110H, both end devices can be notified of a loss of fiber link.

Key Features

IEEE802.3at draft and IEEE802.3af PoE (Power over Ethernet) PSE compatible

n           Internal AC power supply

n           Over-current protection

n           Under-current detection

n           Minimum load sensing

n           Fault Protection Input

n           PSE MDI power enable/disable

LFP (Link Fault Pass-through) and FEF (Far End Fault)

Supports one 10/100/1000Base-T Gigabit Ethernet UTP port and one 1000Base-SX / LX (SC/LC) Gigabit Ethernet Fiber port

Supports 802.3x flow control for full-duplex ports and backpressure for half-duplex ports

Supports comprehensive types of fiber with different distances and connections, including SC/Bidi/LC and so on

Supports auto mode on the TP port

DIP switch to set configurations

n           DIP 1: LFP/LFP DIS

n           DIP 2: PoE/PoE DIS

n           DIP 3: Bridge Mode/Cut Through Mode

Supports jumbo frame (Normal Mode: 2KB, Cut-Through Mode: 9KB)

PSE RJ-45 Pin-out Alternatives A/B Auto detection

RoHS Compliance

 

Specification

Standards
IEEE802.3 10Base-T
IEEE802.3u 100ase-TX

IEEE802.3z/ab 1000Base-T

    ■1000Base-SX/LX
    ■IEEE802.3x full-duplex flow control

Cable
UTPCat. 5 cable and up to 100m
Fiber
1000SX50/125, 62.5/125, or 100/140μm multi-mode
1000LX8.3/125, 8.7/125, 9/125 or 10/125μm single-mode

Cable Connection Parameter

    ■TP Cable LimitationsCat. 5 and up to 100m
    ■Fiber Cable Limitations

 

Multi-Mode Fiber
62.5/125
μm

Multi-Mode Fiber
50/125
μm

 

Bandwidth
MHz-Km

Distance

Bandwidth
MHz-Km

Distance

1000SX
850nm

160

220m

400

500m

200

275m

500

550m

1000LX
1310nm/1550nm

Single-Mode Fiber 9/125μm
Single-Mode transceiver 1310nm: 10/30Km
Single-Mode transceiver 1550nm: 50Km

 

Data Transfer Rate2000Mbps/full-duplex

Network Interface

TP Port

10/100Base-TX
Auto-Negotiation
Auto-MDIX
Flow control for Full-Duplex
Backpressure for Half-Duplex

TP Port

1000Base-T
Auto-Negotiation mode

(( Auto-MDIX only for Auto-Negotiation
Flow control for Full-Duplex only

Fiber Port

1000Base-SX/LX (SC/LC)
with NWay flow control
Link partner must be 1000FDX with NWay flow control

LED Indicator

LED

Color

Function

FX LNK/ACT

Green

Lit when fiber connection is good

Blinks when fiber data is present

TP LNK/ACT

Green

Lit when TP connection is good

Blinks when TP data is present

TP SPD

Green

Amber

Green Lit when TP speed is 1000Mbps

Amber Lit when TP speed is 100Mbps

Off when TP speed is 10Mbps

PWR

Green

Lit when +5V power is coming up

PoE PSE-TP

Green

Lit when PoE feeding power is active

Red

Lit when PoE feeding power is disrupted

(In case of overtemperature/overcurrent  )

Hardware Specification

Feature

Detailed Description

Power Characteristics

Requirement :100 – 240 VAC, 47 –63 Hz

Consumption :Max. up to 35W

Ambient Temperature

0 ~ 40°C

Humidity

5 ~ 90

Dimensions

40 (H) x 158 (W) x 133 (D) mm

Weight

0.6kg

EMI

Comply with FCC Part 15 Class A & CE Mark approval

Packing Information

Carton Dimensions (mm)

pcs/Carton

N.W (KG)

G.W (KG)

40x158x133

14

16.4

17.4

 


 

Ordering Information

PSGC-110HSC

10/100/1000Base-T to 1000Base-X PoE PSE+ GbE converter, SC Multi-Mode

PSGC-110HSC.S10

10/100/1000Base-T to 1000Base-X PoE PSE+ GbE converter, SC Single-Mode 10km

PSGC-110HSC.S30

10/100/1000Base-T to 1000Base-X PoE PSE+ GbE converter, SC Single-Mode 30km

PSGC-110HSC.S50

10/100/1000Base-T to 1000Base-X PoE PSE+ GbE converter, SC Single-Mode 50km

PSGC-110HBS5.S10

10/100/1000Base-T to 1000Base-X PoE PSE+ GbE converter, Bidi SC Single-Mode 10km, 1550nm

PSGC-110HBS3.S10

10/100/1000Base-T to 1000Base-X PoE PSE+ GbE converter, Bidi SC Single-Mode 10km, 1310nm

PSGC-110HBS5.S20

10/100/1000Base-T to 1000Base-X PoE PSE+ GbE converter, Bidi SC Single-Mode 20km, 1550nm

PSGC-110HBS3.S20

10/100/1000Base-T to 1000Base-X PoE PSE+ GbE converter, Bidi SC Single-Mode 20km, 1310nm

PSGC-110HLC

10/100/1000Base-T to 1000Base-X PoE PSE+ GbE converter, LC Multi-Mode 850nm

PSGC-110HLC.S10

10/100/1000Base-T to 1000Base-X PoE PSE+ GbE converter, LC Single-Mode 10km

PSGC-110HLC.S30

10/100/1000Base-T to 1000Base-X PoE PSE+ GbE converter, LC Single-Mode 30km

PSGC-110HLC.S50

10/100/1000Base-T to 1000Base-X PoE PSE+ GbE converter, LC Single-Mode 50km

  Search
 
 Home | Ruby | News | Products | Solution | Support | Partner | Contact