Industrial - Rubytech

Ethernet Ring Protection Switching Solution

rubyadmin — Wed, 09 Jan 2019 13:31:36 +0000

Ethernet Ring Protection Switching, or ERPS, is an effort at ITU-T under G.8032 Recommendation to provide sub-50ms protection and recovery switching for Ethernet traffic in a ring topology and at the same time ensuring that there are no loops formed at the Ethernet layer. G.8032v1 supported a single ring topology and G.8032v2 supports multiple rings/ladder topology.

ERPS specifies protection switching mechanisms and a protocol for Ethernet layer network (ETH) rings. Ethernet Rings can provide wide-area multipoint connectivity more economically due to their reduced number of links. The mechanisms and protocol defined in this Recommendation achieve highly reliable and stable protection; and never form loops, which would fatally affect network operation and service availability.

Each Ethernet Ring Node is connected to adjacent Ethernet Ring Nodes participating in the same Ethernet Ring, using two independent links. A ring link is bounded by two adjacent Ethernet Ring Nodes, and a port for a ring link is called a ring port. The minimum number of Ethernet Ring Nodes in an Ethernet Ring is three.

The fundamentals of this ring protection switching architecture are:
a) The principle of loop avoidance.
b) The utilization of learning, forwarding, and Filtering Database (FDB) mechanisms defined in the Ethernet flow forwarding function (ETH_FF).

Loop avoidance in an Ethernet Ring is achieved by guaranteeing that, at any time, traffic may flow on all but one of the ring links. This particular link is called the Ring Protection Link (RPL), and under normal conditions this ring link is blocked, i.e. not used for service traffic. One designated Ethernet Ring Node, the RPL Owner Node, is responsible for blocking traffic at one end of the RPL. Under an Ethernet ring failure condition, the RPL Owner Node is responsible for unblocking its end of the RPL (unless the RPL has failed) allowing the RPL to be used for traffic. The other Ethernet Ring Node adjacent to the RPL, the RPL Neighbour Node, may also participate in blocking or unblocking its end of the RPL.

The event of an Ethernet Ring failure results in protection switching of the traffic. This is achieved under the control of the ETH_FF functions on all Ethernet Ring Nodes. An APS protocol is used to coordinate the protection actions over the ring.

The post Ethernet Ring Protection Switching Solution first appeared on Rubytech.

IGS-2700 and IPGS-2700 series industrial switches

rubyadmin — Wed, 09 Jan 2019 13:18:30 +0000

IGS-2700 and IPGS-2700 Series
Industrial L2+ Managed GbE Switches

The IGS-2700 and IPGS-2700 series industrial L2+ managed GbE switches are the next generation industrial grade Ethernet switches offering powerful L2 and basic L3 features with better functionality and usability. In addition to the extensive management features, the IGS-2700 and IPGS-2700 series also provide carrier Ethernet features such as OAM/CFM/ERPS/EPS/PTPv2, of which make them suitable for industrial and carrier Ethernet applications.

The IGS-2700 and IPGS-2700 series consist of 6 non-PoE models which are IGS-2704A, IGS-2706A, IGS-2708A, IGS-2708B, IGS-2710G and IGS-2712B, and 8 PoE+ models which are IPGS-2706A, IPGS-2708A, IPGS-2708B, IPGS-2710AT, IPGS-2710A, IPGS-2710G, IPGS-2712B and IPGS-2710AM, and 3 UPoE models which are IPGS-2708AU, IPGS-2708BU, and IPGS-2712BU. The series offer users with various options of port combinations and PoE++ budget, in order to meet different requirements in various applications.

The embedded Device Managed System (DMS) features provides users with the benefits of easy-to-use/configure/install/troubleshoot in the video surveillance, wireless access, and other industrial applications. The IGS-2700 and IPGS-2700 series are ideal to deliver management simplicity, better user experience, and lowest total cost of ownership.

Key Features

Rapid Ring (R-Ring)
Built in Device Management System (DMS)
ITU-T G.8031 Ethernet Linear Protection Switching (EPS)
ITU-T G.8032 Ethernet Ring Protection Switching (ERPS)
IEEE 1588v2 PTP
IEEE 802.3ah OAM
IEEE 802.1ag CFM (ITU-T Y.1731 Performance monitoring)
DHCP Server
IEEE 802.3az Energy Efficient Ethernet standard for green Ethernet application
IEEE 802.3af/at/UPoE Power over Ethernet
IPv4/IPv6 L3 static route

Benefits

Feature-rich Specifications to Support Various Applications

The series deliver extensive industrial and carrier grade functionalities, including R-Ring, ITU-T G.8031, ITU-T G.8032, IEEE 1588v2 PTP, OAM, CFM, etc. The product series also have enhanced L2/L3 features for better manageability and usability.
The PoE+(30W) and UPoE(60W) models provide advanced PoE features such as PoE auto-checking, PoE scheduling, and PoE power delay for users to manage the powered devices more easily. With extensive PoE+ mode configured, the series can even provide power with up to 38W per port.
It offers users with better price/performance ratio in industrial application, and provide secure and reliable functionalities for metro/carrier Ethernet deployments.
Exceptional Precision with IEEE 1588v2 PTP

The switch performs IEEE1588v2 PTP, with transparent clock capability, implementations in hardware, so there is no performance penalty on packet processing.
The hardware architecture ensures low latency and high time accuracy – which is critical for delay-sensitive financial and mobile applications.
Superior Reliability through OAM and CFM for Service Assurance

Service assurance is provided through a rich feature set of operations, administration, and maintenance (OAM) functionalities. It can simplify and facilitate the management of Carrier network, resulting in diminishing operational costs.
The Ethernet access device also offers standards-based fault and performance management in adherence with 1731 PM and 802.1ag connectivity fault management (CFM) standards.
These features contribute to significant reduction in operational expenditures and allows for troubleshooting without expensive truck rolls.
Easy to Install, Configure and Troubleshoot by Device Management System

The DMS provides embedded functions to facilitate devices management at anytime and anywhere. Its user-friendly interface helps users to manage devices intuitively.
It supports various IP device types (e.g. PC, IP-phone, IP-camera, WiFi-AP) for end users to enhance manageability and save time/cost during installation/maintenance stages.
Lowing Total Cost of Ownership (TCO) with Energy-efficient Design

The switch is designed to help companies to save power needs and reduce TCO by Energy Efficient Ethernet (IEEE 802.3az). It can be used for customers to build a green Ethernet networking environment.

Specifications

Port Configuration

Model Name	Total Ports	RJ45 10M/ 100M/1G	Uplinks 100M/1G	Console	Available PoE Power	Ring Mgmt.	DI/DO
IGS-2704A	4	2	2 SFP	RJ45	--	DIP	1/1
IGS-2706A	6	4	2 SFP	RJ45	--	DIP	1/1
IGS-2708A	8	6	2 SFP	RJ45	--	DIP	1/1
IGS-2708B	8	4	4 SFP	RJ45	--	DIP	1/1
IGS-2710G	10	8	2 Combo	RJ45	--	DIP	1/1
IGS-2712B	12	8	4 SFP	RJ45	--	DIP	1/1
IPGS-2706A	6	4	2 SFP	RJ45	120W	DIP	1/1
IPGS-2708A	8	6	2 SFP	RJ45	120W	DIP	1/1
IPGS-2708B	8	4	4 SFP	RJ45	120W	DIP	1/1
IPGS-2710A	10	8	2 SFP	RJ45	240W	DIP	1/1
IPGS-2710AT	10	8	2 SFP	RJ45	480W	DIP	1/1
IPGS-2710AM	10	8	2 SFP	RJ45	720W	DIP	1/1
IPGS-2710G	10	8	2 Combo	RJ45	240W	DIP	1/1
IPGS-2712B	12	8	4 SFP	RJ45	240W	DIP	1/1
IPGS-2708AU	8	6	2 SFP	RJ45	240W	DIP	1/1
IPGS-2708BU	8	4	4 SFP	RJ45	240W	DIP	1/1
IPGS-2712BU	12	8	4 SFP	RJ45	240W	DIP	1/1

Hardware Performance

Model Name	Forwarding Capacity (Mpps)	Switching Capacity (Gbps)	Mac Table (K)	Jumbo Frames (bytes)
IGS-2704A	5.952	8	8	9600
IGS-2706A	8.928	12	8	9600
IGS-2708A	11.904	16	8	9600
IGS-2708B	11.904	16	8	9600
IGS-2710G	14.88	20	8	9600
IGS-2712B	17.856	24	8	9600
IPGS-2706A	8.928	12	8	9600
IPGS-2708A	11.904	16	8	9600
IPGS-2708B	11.904	16	8	9600
IPGS-2710A	14.88	20	8	9600
IPGS-2710AT	14.88	20	8	9600
IPGS-2710AM	14.88	20	8	9600
IPGS-2710G	14.88	20	8	9600
IPGS-2712B	17.856	24	8	9600
IPGS-2708AU	11.904	16	8	9600
IPGS-2708BU	11.904	16	8	9600
IPGS-2712BU	17.856	24	8	9600

Environmental Range

Operating Temperature		Storage Temperature		Operating Humidity	Altitude
Fahrenheit	Centigrade	Fahrenheit	Centigrade	Operating Humidity	Feet	Meters
-40 to 167	-40 to 75	-40 to 185	-40 to 85	5% to 95% non-condensing	<10000	<3000

Dimension, Weights, Mounting

Model Name	Dimension (WxHxD)		Weight		Mounting Type
Model Name	Millimeter	Inches	Kilograms	Pounds	Mounting Type
IGS-2704A	62x135x130	2.4x5.3x5.1	< 1	<2.2	DIN rail
IGS-2706A	62x135x130	2.4x5.3x5.1	< 1	<2.2	DIN rail
IGS-2708A	62x135x130	2.4x5.3x5.1	< 1	<2.2	DIN rail
IGS-2708B	62x135x130	2.4x5.3x5.1	< 1	<2.2	DIN rail
IGS-2710G	62x135x130	2.4x5.3x5.1	< 1	<2.2	DIN rail
IGS-2712B	62x135x130	2.4x5.3x5.1	< 1	<2.2	DIN rail
IPGS-2706A	62x135x130	2.4x5.3x5.1	< 1	<2.2	DIN rail
IPGS-2708A	62x135x130	2.4x5.3x5.1	< 1	<2.2	DIN rail
IPGS-2708B	62x135x130	2.4x5.3x5.1	< 1	<2.2	DIN rail
IPGS-2710A	62x135x130	2.4x5.3x5.1	< 1	<2.2	DIN rail
IPGS-2710AT	70X168X130	2.76x5.3x5.1	1.2	2.65	DIN rail
IPGS-2710AM	62x135x130	2.4x5.3x5.1	< 1	<2.2	DIN rail
IPGS-2710G	62x135x130	2.4x5.3x5.1	< 1	<2.2	DIN rail
IPGS-2712B	62x135x130	2.4x5.3x5.1	< 1	<2.2	DIN rail
IPGS-2708AU	62x135x130	2.4x5.3x5.1	< 1	<2.2	DIN rail
IPGS-2708BU	62x135x130	2.4x5.3x5.1	< 1	<2.2	DIN rail
IPGS-2712BU	62x135x130	2.4x5.3x5.1	< 1	<2.2	DIN rail

Voltage and Frequency

Primary Power Supply - DC Input Voltage
Voltage	Frequency
DC Nominal	12/24/48 VDC dual inputs (non-PoE model) 54 VDC dual inputs (PoE model)
DC Operating Range	12 to 48 VDC (non-PoE model) 48 to 57 VDC (PoE model)
PoE SKUs	Required >48 VDC for PoE IEEE 802.3af (Max. 15.4W) output Required >54 VDC for PoE+ IEEE802.3at (Max. 30W) output Required >54 VDC for UPoE (Max. 60W) output

PoE Power Capacity

Model Name	Available PoE Power	Number of Ports That Support PoE(15.4W), PoE+(30.0W), or UPoE(60W)
IPGS-2706A	120W	Each of port 1 - 4 support PoE/ PoE+ within available PoE Power ( per port 38W by request )
IPGS-2708A	120W	Each of port 1 - 4 support PoE/ PoE+ within available PoE Power ( per port 38W by request )
IPGS-2708B	120W	Each of port 1 - 4 support PoE/ PoE+ within available PoE Power ( per port 38W by request )
IPGS-2710A	240W	Each of port 1 - 4 support PoE/ PoE+ within available PoE Power ( per port 38W by request )
IPGS-2710AT	480W	Each of port 1 - 8 support PoE/ PoE+/PoE++ within available PoE Power
IPGS-2710AM	720W	Each of port 1 - 8 support PoE++ within available PoE Power
IPGS-2710G	240W	Each of port 1 - 8 support PoE/ PoE+ within available PoE Power ( per port 38W by request )
IPGS-2712B	240W	Each of port 1 - 8 support PoE/ PoE+ within available PoE Power ( per port 38W by request )
IPGS-2708AU	240W	Each of port 1 - 4 support UPOE within available PoE Power
IPGS-2708BU	240W	Each of port 1 - 4 support UPOE within available PoE Power
IPGS-2712BU	240W	Each of port 1 - 4 support UPOE within available PoE Power

Certifications

Electromagnetic Emissions (EMC)
SHALL comply with European Directives for CE marking (LVD with EN 62368-1) SHALL comply with FCC Part 15 Class A UL 62386-1will be designed, UL report is customer request Other by Request

Software Features

Layer 2 Switching
Spanning Tree Protocol (STP)	Standard Spanning Tree 802.1d: Spanning Tree Protocol is an OSI layer-2 protocol which ensures a loop free topology for any bridged LAN Rapid Spanning Tree (RSTP) 802.1w: Rapid Spanning Tree Protocol, which provides for faster spanning tree convergence after a topology change Multiple Spanning Tree (MSTP) 802.1s: Multiple Spanning Tree Protocol. The MSTP protocol provides for multiple spanning tree instances
VLAN	802.1Q tag-based VLAN: Supports up to 4K VLANs simultaneously (out of 4096 VLAN IDs) Port-based VLAN: A port member of a VLAN can be isolated to other isolated ports on the same VLAN and Private VLAN Private VLAN Edge (PVE): Private VLANs are based on the source port mask, and there are no connections to VLANs. This means that VLAN IDs and Private VLAN IDs can be identical Voice VLAN: The Voice VLAN feature enables voice traffic forwarding on the Voice VLAN Guest VLAN: The IEEE 802.1X Guest VLAN feature allows a guest VLAN to be configured for each 802.1X port on the device to provide limited services to non-802.1X-compliant clients Q-in-Q (double tag) VLAN: Business customers of service providers often have specific requirements for VLAN IDs and the number of VLANs to be supported 802.1v Protocol VLAN: Classifying multiple protocols into a single VLAN often imposes VLAN boundaries that are inappropriate for some of the protocols, requiring the presence of a non-standard entity to relay between VLANs the frames bearing the protocols for which the VLAN boundaries are inappropriate MAC-based VLAN: The MAC-based VLAN feature allows incoming untagged packets to be assigned to a VLAN and thus classify traffic based on the source MAC address of the packet IP Subnet-Based VLAN: In an IP subnet–based VLAN, all the end workstations in an IP subnet are assigned to the same VLAN. In this VLAN, users can move their workstations without reconfiguring their network addresses Management VLAN: Management VLAN is used for managing the switch from a remote location by using protocols such as telnet, SSH, SNMP, syslog etc
LACP Trunking	Link Aggregation Control Protocol (LACP) IEEE 802.3ad: Controls whether LACP is enabled on this switch port. LACP will form an aggregation when 2 or more ports are connected to the same partner Up to 26 groups Up to 8 ports per group
GARP VLAN Registration Protocol (GVRP)	GVRP stands for GARP (Generic Attribute Registration Protocol) VLAN Registration Protocol. It’s a Layer 2 network protocol, for automatic configuration of switches in a VLAN network
DHCP Relay	Relay of DHCP traffic to DHCP server in different VLAN Works with DHCP Option 82
IGMP v1/v2/v3 Snooping	IGMP limits bandwidth-intensive multicast traffic to only the requesters. Supports 1024 multicast groups
IGMP Querier	IGMP querier is used to support a Layer 2 multicast domain of snooping switches in the absence of a multicast router
IGMP Proxy	IGMP snooping with proxy reporting or report suppression actively filters IGMP packets in order to reduce load on the multicast router
MLD v1/v2 Snooping	Delivers IPv6 multicast packets only to the required receivers
Multicast VLAN Registration (MVR)	It uses a dedicated manually configured VLAN, called the multicast VLAN, to forward multicast traffic over Layer 2 network in conjunction with IGMP snooping
Layer 3 Switching
IPv4 Static Routing	IPv4 Unicast: Static routing
IPv6 Static Routing	IPv6 Unicast: Static routing
Quality of Service
Hardware Queue	Supports 8 hardware queues
Classification	Port based: Traffic QoS by Port 802.1p: VLAN priority based Layer 2 CoS QoS, Class of service is a parameter used in data and voice protocols to differentiate the types of payloads contained in the packet being transmitted DSCP based Differentiated Services (DiffServ) Layer 3 DSCP QoS: IP packets can carry either an IP precedence (IPP) value or a Differentiated Services Code Point (DSCP) value. QoS supports the use of either value because DSCP values are backward-compatible with IP precedence values Classification and re-marking TCP/IP ACLs: QoS by ACL
Rate Limiting	Ingress policer Egress shaping and rate control Per port
Scheduling	Strict priority and weighted round-robin (WRR): Weighted Round Robin is a scheduling algorithm that uses weights assigned to queues to determine how much data will be emptied from a queue before moving to the next queue
Security
ACLs	Supports up to 512 entries. Drop or rate limitation based on: Source and destination MAC, VLAN ID or IP address, protocol, port Differentiated services code point (DSCP) / IP precedence TCP/ UDP source and destination ports 802.1p priority Ethernet type Internet Control Message Protocol (ICMP) packets TCP flag
Port Security	Locks MAC addresses to ports, and limits the number of learned MAC address
IP Source Guard	Prevents illegal IP address from accessing to specific port in the switch
Storm Control	Prevents traffic on a LAN from being disrupted by a broadcast, multicast, or unicast storm on a port
IEEE 802.1X	IEEE802.1X: RADIUS authentication, authorization and accounting, MD5 hash, guest VLAN, single/multiple host mode and single/multiple sessions Supports IGMP-RADIUS based 802.1X Dynamic VLAN assignment
TACACS+	Supports TACACS+ authentication. Switch as a client
Secure Shell (SSH)	SSH secures Telnet traffic in or out of the switch, SSH v1 and v2 are supported
Secure Sockets Layer (SSL)	SSL encrypts the http traffic, allowing advanced secure access to the browser-based management GUI in the switch
HTTPs and SSL (Secured Web)	Hyper Text Transfer Protocol Secure (HTTPS) is the secure version of HTTP
BPDU Guard	The BPDU guard, an enhancement to STP, removes a node that reflects BPDUs back in the network. It enforces the STP domain borders and keeps the active topology predictable by not allowing any network devices behind a BPDU guard-enabled port to participate in STP
DHCP Snooping	A feature acts as a firewall between untrusted hosts and trusted DHCP servers
Loop Protection	To prevent unknown unicast, broadcast and multicast loops in Layer 2 switching configurations.
Management
DHCP	DHCP Server: Support DHCP server to assign IP to DHCP clients DHCP client: The Dynamic Host Configuration Protocol (DHCP) is a standardized network protocol used on Internet Protocol (IP) networks for dynamically distributing network configuration parameters, such as IP addresses for interfaces and services
Event/Error Log	Support SNMP Trap/Syslog/SMTP
SNMP	SNMP version1, 2c and 3 with support for traps, and SNMP version 3 user-based security model (USM)
Remote Monitoring (RMON)	Embedded RMON agent supports RMON groups 1,2,3,9 (history, statistics, alarms, and events) for enhanced traffic management, monitoring and analysis
Firmware Upgrade	Web browser upgrade (HTTP/ HTTPs) and TFTP Upgrade through console port as well
Configuration Export/Import	update of the firmware controlling the switch
Port Mirroring	Traffic on a port can be mirrored to another port for analysis with a network analyzer or RMON probe. Up to N-1 (N is Switch’s Ports) ports can be mirrored to single destination port. A single session is supported
IEEE 802.1ab (LLDP)	Used by network devices for advertising their identities, capabilities, and neighbors on an IEEE 802ab local area network Support LLDP-MED (ANSI/TIA-1057) extensions
UPnP	The Universal Plug and Play Forum, an industry group of companies working to enable device-to-device interoperability by promoting Universal Plug and Play
CDP Aware	The CDP operation is restricted to decoding incoming CDP frames (The switch doesn’t transmit CDP frames). CDP frames are only decoded if LLDP on the port is enabled
s-Flow	The industry standard for monitoring high speed switched networks. It gives complete visibility into the use of networks enabling performance optimization, accounting/billing for usage, and defense against security threats
Web GUI Interface	Built-in switch configuration utility for browser-based device configuration
CLI	For users to configure/manage switches in command line modes
Dual Image	Independent primary and secondary images for backup while upgrading
NTP	Network Time Protocol (NTP) is a networking protocol for clock synchronization between computer systems over packet-switched
Switch Management	HTTP/HTTPs SSH DHCP Client/ DHCPv6 Client Telnet Client IPv6 Management
Diagnostics	Cable diagnostics Ping Syslog
Device Management System (DMS)
Graphical Monitoring	Topology view: Support intuitive way to configure and manage switches and devices with visual relations Floor view: It’s easy to drag and drop PoE devices and help you to build smart workforces Map view: Enhance efficiency to drag and drop devices and monitor surroundings on google map Display visual chart of network traffic of all devices and monitor every port at any time from switches
Find my Switch	Search your real switches quickly and manage directly
Technical Support Online	Provide technical assistance to the user remotely
Traffic Monitoring	Display visual chart of network traffic of all devices and monitor every port at any time from switches
Trouble Shooting	Network diagnostic between master switch and devices Support protection mechanism, such as rate-limiting to protect your devices from brute-force downloading
Power over Ethernet (PoE)
Port Configuration	Supports per port PoE configuration function
PoE Scheduling	Supports per port PoE scheduling to turn on/off the PoE devices (PDs).
Auto-checking	Check the link status of PDs. Reboot PDs if there is no responses
Power Delay	The switch provides power to the PDs based on delay time when PoE switch boots up, in order to protect switch from misuse of the PDs

The post IGS-2700 and IPGS-2700 series industrial switches first appeared on Rubytech.

Surge 6KV Industrial grade Ethernet switches Solution

rubyadmin — Wed, 09 Jan 2019 10:28:17 +0000

The IGS-2732 and IPGS-2732 series industrial L2+ managed GbE switches, which is specially designed for security digital monitor transmission. It supports 6KV surge immunity, preventing the port from the damage caused by indirect lightning and ensuring the reliability of data transmission. The switch is widely used in security video monitoring and networking of small & medium size enterprises

The IGS-2732 and IPGS-2732 series industrial L2+ managed GbE switches are the next generation industrial grade Ethernet switches offering powerful L2 and basic L3 features with better functionality and usability. In addition to the extensive management features, the IGS-2732 and IPGS-2732 series also provide carrier Ethernet features such as OAM/CFM/ERPS/EPS/PTPv2, of which make them suitable for industrial and carrier Ethernet applications.

The IGS-2732 and IPGS-2732 series consist of 4 non-PoE models which are IGS-2732X-AD, IGS-2732X-HD, IGS-2722X-AD and IGS-2722X-HD, and 2 PoE+ models which are IPGS-2732X-AD and IPGS-2722X-AD. The series offer users with various options of port combinations and PoE+ budget, in order to meet different requirements in various applications.The embedded Device Managed System (DMS) features provides users with the benefits of easy-to-use/configure/install/troubleshoot in the video surveillance, wireless access, and other industrial applications. The IGS-2732 and IPGS-2732 series are ideal to deliver management simplicity, better user experience, and lowest total cost of ownership.

The post Surge 6KV Industrial grade Ethernet switches Solution first appeared on Rubytech.

IGS-2724 and IPGS-2724 series industrial switches

jesse wang — Wed, 09 Jan 2019 09:24:47 +0000

IGS-2724 and IPGS-2724 Series
Industrial L2+ Managed GbE Switches

The IGS-2724 and IPGS-2724 series industrial L2+ managed GbE switches are the next generation industrial grade Ethernet switches offering powerful L2 and basic L3 features with better functionality and usability. In addition to the extensive management features, the IGS-2724 and IPGS-2724 series also provide carrier Ethernet features such as OAM/CFM/ERPS/EPS/PTPv2, of which make them suitable for industrial and carrier Ethernet applications.

The IGS-2724 and IPGS-2724 series consist of 2 non-PoE models which are IGS-2724K-AD and IGS-2720B-AD, and 4 PoE+ models which are IPGS-2724K-AD, IPGS-2724K-D, IPGS-2720B-AD and IPGS-2720B-D. The series offer users with various options of port combinations and PoE+ budget, in order to meet different requirements in various applications.

The embedded Device Managed System (DMS) features provides users with the benefits of easy-to-use/configure/install/troubleshoot in the video surveillance, wireless access, and other industrial applications. The IGS-2724 and IPGS-2724 series are ideal to deliver management simplicity, better user experience, and lowest total cost of ownership.

Key Features

Rapid Ring (R-Ring)
Built in Device Management System (DMS)
ITU-T G.8031 Ethernet Linear Protection Switching (EPS)
ITU-T G.8032 Ethernet Ring Protection Switching (ERPS)
IEEE 1588v2 PTP
IEEE 802.3ah OAM
IEEE 802.1ag CFM (ITU-T Y.1731 Performance monitoring)
DHCP Server
IEEE 802.3az Energy Efficient Ethernet standard for green Ethernet application
IEEE 802.3af/at Power over Ethernet
IPv4/IPv6 L3 static route

Benefits

Feature-rich Specifications to Support Various Applications

The series deliver extensive industrial and carrier grade functionalities, including R-Ring, ITU-T G.8031, ITU-T G.8032, IEEE 1588v2 PTP, OAM, CFM, etc. The product series also have enhanced L2/L3 features for better manageability and usability.
It offers users with better price/performance ratio in industrial application, and provide secure and reliable functionalities for metro/carrier Ethernet deployments.
Exceptional Precision with IEEE 1588v2 PTP

The switch performs IEEE1588v2 PTP with transparent clock capability, implementations in hardware, so there is no performance penalty on packet processing.
The hardware architecture ensures low latency and high time accuracy – which is critical for delay-sensitive financial and mobile applications.
Superior Reliability through OAM and CFM for Service Assurance

Service assurance is provided through a rich feature set of operations, administration, and maintenance (OAM) functionalities. It can simplify and facilitate the management of Carrier network, resulting in diminishing operational costs.
The Ethernet access device also offers standards-based fault and performance management in adherence with 1731 PM and 802.1ag connectivity fault management (CFM) standards.
These features contribute to significant reduction in operational expenditures and allows for troubleshooting without expensive truck rolls.
Easy to Install, Configure and Troubleshoot by Device Management System

The DMS provides embedded functions to facilitate devices management at anytime and anywhere. Its user-friendly interface helps users to manage devices intuitively.
It supports various IP device types (e.g. PC, IP-phone, IP-camera, WiFi-AP) for end users to enhance manageability and save time/cost during installation/maintenance stages.
Lowing Total Cost of Ownership (TCO) with Energy-efficient Design

The switch is designed to help companies to save power needs and reduce TCO by Energy Efficient Ethernet (IEEE 802.3az). It can be used for customers to build a green Ethernet networking environment.

Specifications

Port Configuration

Model Name	Total Ports	RJ45 (10M/100M/1G)	Uplinks	Console	Available PoE Power
IGS-2724K-AD	24	20	4 RJ45/SFP combo	RJ45	--
IGS-2720B-AD	20	16	4 SFP	RJ45	--
IPGS-2724K-D	24	20	4 RJ45/SFP combo	RJ45	370W (DC Input)
IPGS-2724K-AD	24	20	4 RJ45/SFP combo	RJ45	370W (DC Input)
IPGS-2720B-D	20	16	4 SFP	RJ45	250W (DC Input)
IPGS-2720B-AD	20	16	4 SFP	RJ45	250W (DC Input)

Hardware Performance

Model Name	Forwarding Capacity (Mpps)	Switching Capacity (Gbps)	Mac Table (K)	Jumbo Frames (Bytes)
IGS-2724K-AD	35.714	48	8	9600
IGS-2720B-AD	29.761	40	8	9600
IPGS-2724K-D	35.714	48	8	9600
IPGS-2724K-AD	35.714	48	8	9600
IPGS-2720B-D	29.761	40	8	9600
IPGS-2720B-AD	29.761	40	8	9600

Environmental Range

Operating Temperature		Storage Temperature		Operating Humidity	Altitude
Fahrenheit	Centigrade	Fahrenheit	Centigrade	10% to 90% non-condensing	Feet	Meters
-40 to 167	-40 to 75	-40 to 185	-40 to 85	10% to 90% non-condensing	<10000	<3000

Dimension, Weights, Mounting

Model Name	Dimension (WxHxD)		Weight		Mounting Type
Model Name	Millimeter	Inches	Kilograms	Pounds	Mounting Type
IGS-2724K-AD	442x44x300	17.4x1.7x11.8	TBD	TBD	Desktop,Rack
IGS-2720B-AD	442x44x300	17.4x1.7x11.8	TBD	TBD	Desktop,Rack
IPGS-2724K-D	442x44x300	17.4x1.7x11.8	TBD	TBD	Desktop,Rack
IPGS-2724K-AD	442x44x300	17.4x1.7x11.8	4.7	10.34	Desktop,Rack
IPGS-2720B-D	442x44x300	17.4x1.7x11.8	TBD	TBD	Desktop,Rack
IPGS-2720B-AD	442x44x300	17.4x1.7x11.8	4.3	9.46	Desktop,Rack

Voltage and Frequency

Input Voltage and Frequency
AC Voltage	100-240 VAC (except IPGS-2724K-D,IPGS-2720B-D)
DC Nominal	24/48 VDC dual inputs (non-PoE model) 54 VDC dual inputs (PoE model)
DC Operating Range	18 to 57 VDC (non-PoE model) 52 to 57 VDC (PoE model)
PoE SKUs	Required>48 VDC for PoE IEEE 802.3af (Max. 15.4W) output Required>54 VDC for PoE+IEEE802.3at (Max. 30W) output

PoE Power Capacity

Model Name	Available PoE Power	Number of Ports That Support PoE(15.4W) and PoE+(30.0W)
IPGS-2724K-D	370W (DC Input)	Each of port 1- 20 support PoE/ PoE+ within available PoE Power
IPGS-2724K-AD	370W (DC Input)	Each of port 1- 20 support PoE/ PoE+ within available PoE Power
IPGS-2720B-D	250W (DC Input)	Each of port 1- 16 support PoE/ PoE+ within available PoE Power
IPGS-2720B-AD	250W (DC Input)	Each of port 1- 16 support PoE/ PoE+ within available PoE Power

Certifications

Electromagnetic Emissions (EMC)
SHALL comply with European Directives for CE marking (LVD with EN 62368-1) SHALL comply with FCC Part 15 Class A UL 62386-1will be designed, UL report is customer request Other by Request

Software Features

Ring Management
ITU-T G.8031	Supports ITU-T G.8031 Ethernet Linear Protection Switching
ITU-T G.8032	Supports ITU-T G.8032 Ethernet Ring Protection Switching
Rapid Ring	Enable self-recover time in less than 20ms
Device Management System (DMS)
Graphical Monitoring	Topology view: Support intuitive way to configure and manage switches and devices with visual relations Floor view: It’s easy to drag and drop PoE devices and help you to build smart workforces Map view: Enhance efficiency to drag and drop devices and monitor surroundings on google map
Find my Switch	Search and manage your real switches quickly.
Traffic Monitoring	Display visual chart of network traffic of all devices and monitor every port at any time from switches
Trouble Shooting	Network diagnostic between master switch and devices Support protection mechanism, such as rate-limiting to protect your devices from brute-force downloading Support performance management and link management through IEEE 802.3ah and IEEE 802.1ag (Y.1731)
Ethernet OAM
IEEE 802.3ah OAM	Supports Operations, Administration & Management
IEEE 802.1ag & ITU-T Y.1731 Flow OAM	Supports IEEE 802.1ag Ethernet CFM (Connectivity Fault Management) Supports ITU-T Y.1731 Performance Monitoring
ITU-T Y.1564	Support RFC2544 Ethernet Service Activation Test Benchmarking Methodology:Throughput, Latency, Frame loss rate, Back-to-back frames Test
Layer 2 Switching
Spanning Tree Protocol (STP)	Standard Spanning Tree 802.1d Rapid Spanning Tree (RSTP) 802.1w Multiple Spanning Tree (MSTP) 802.1s
Trunking	Link Aggregation Control Protocol (LACP) IEEE 802.3ad Up to 16 groups and up to 16 ports per group
VLAN	Port-based VLAN 802.1Q tag-based VLAN MAC-based VLAN Management VLAN Private VLAN Edge (PVE) Q-in-Q (double tag) VLAN Voice VLAN GARP VLAN Registration Protocol (GVRP)
DHCP Relay	Relay of DHCP traffic to DHCP server in different VLAN. Works with DHCP Option 82
IGMP v1/v2/v3 Snooping	IGMP limits bandwidth-intensive multicast traffic to only the requesters. Supports 1024 multicast groups
IGMP Querier	IGMP querier is used to support a Layer 2 multicast domain of snooping switches in the absence of a multicast router
IGMP Proxy	IGMP snooping with proxy reporting or report suppression actively filters IGMP packets in order to reduce load on the multicast router
MLD v1/v2 Snooping	Delivers IPv6 multicast packets only to the required receivers
Multicast VLAN Registration (MVR)	It uses a dedicated manually configured VLAN, called the multicast VLAN, to forward multicast traffic over Layer 2 network in conjunction with IGMP snooping.
Layer 3 Switching
IPv4 Static Routing	IPv4 Unicast: Static routing
IPv6 Static Routing	IPv6 Unicast: Static routing
Security
Secure Shell (SSH)	SSH secures Telnet traffic in or out of the switch, SSH v1 and v2 are supported
Secure Sockets Layer (SSL)	SSL encrypts the http traffic, allowing advanced secure access to the browser-based management GUI in the switch
IEEE 802.1X	IEEE802.1X: RADIUS authentication, authorization and accounting, MD5 hash, guest VLAN, single/multiple host mode and single/multiple sessions Supports IGMP-RADIUS based 802.1X Dynamic VLAN assignment
Layer 2 Isolation Private VLAN Edge	PVE (also known as protected ports) provides L2 isolation between clients in the same VLAN. Supports multiple uplinks
Port Security	Locks MAC addresses to ports, and limits the number of learned MAC address
IP Source Guard	Prevents illegal IP address from accessing to specific port in the switch
RADIUS/ TACACS+	Supports RADIUS and TACACS+ authentication. Switch as a client
Storm Control	Prevents traffic on a LAN from being disrupted by a broadcast, multicast, or unicast storm on a port
DHCP Snooping	A feature acts as a firewall between untrusted hosts and trusted DHCP servers
ACLs	Supports up to 256 entries. Drop or rate limitation based on: Source and destination MAC, VLAN ID or IP address, protocol, port Differentiated services code point (DSCP) / IP precedence TCP/ UDP source and destination ports 802.1p priority Ethernet type Internet Control Message Protocol (ICMP) packets TCP flag
Loop Protection	To prevent unknown unicast, broadcast and multicast loops in Layer 2 switching configurations.
Quality of Service
Hardware Queue	Supports 8 hardware queues
Scheduling	Strict priority and weighted round-robin (WRR) Queue assignment based on DSCP and class of service
Classification	Port based 802.1p VLAN priority based IPv4/IPv6 precedence / DSCP based Differentiated Services (DiffServ) Classification and re-marking ACLs
Rate Limiting	Ingress policer Egress shaping and rate control Per port
Management
HW Monitoring	Temperature Detection and Alarm
HW Watchdog	Supported to resume operation from CPU hang up
IEEE 1588v2 PTP	Support IEEE 1588 v2 PTP (Precision Time Protocol)
DHCP Server	Support DHCP server to assign IP to DHCP clients
Remote Monitoring (RMON)	Embedded RMON agent supports RMON groups 1,2,3,9 (history, statistics, alarms, and events) for enhanced traffic management, monitoring and analysis
Port Mirroring	Traffic on a port can be mirrored to another port for analysis with a network analyzer or RMON probe. Up to N-1 (N is Switch’s Ports) ports can be mirrored to single destination port. A single session is supported.
UPnP	The Universal Plug and Play Forum, an industry group of companies working to enable device-to-device interoperability by promoting Universal Plug and Play
s-Flow	The industry standard for monitoring high speed switched networks. It gives complete visibility into the use of networks enabling performance optimization, accounting/billing for usage, and defense against security threats
IEEE 802.1ab (LLDP)	Used by network devices for advertising their identities, capabilities, and neighbors on an IEEE 802ab local area network Support LLDP-MED extensions
Web GUI Interface	Built-in switch configuration utility for browser-based device configuration
CLI	For users to configure/manage switches in command line modes
Dual Image	Independent primary and secondary images for backup while upgrading
SNMP	SNMP version1, 2c and 3 with support for traps, and SNMP version 3 user-based security model (USM)
Firmware Upgrade	Web browser upgrade (HTTP/ HTTPs) and TFTP Upgrade through console port as well
NTP	Network Time Protocol (NTP) is a networking protocol for clock synchronization between computer systems over packet-switched
Other Management	HTTP/HTTPs; SSH DHCP Client/ DHCPv6 Client Cable Diagnostics Ping Syslog IPv6 Management
Power over Ethernet (PoE)
Port Configuration	Supports per port PoE configuration function
PoE Scheduling	Supports per port PoE scheduling to turn on/off the PoE devices (PDs).
Auto-checking	Check the link status of PDs. Reboot PDs if there is no responses.
Power Delay	The switch provides power to the PDs based on delay time when PoE switch boots up, in order to protect switch from misuse of the PDs

[cq_vc_accordion contentcolor=”#333333″][/cq_vc_accordion]

The post IGS-2724 and IPGS-2724 series industrial switches first appeared on Rubytech.

Industrial - Rubytech

Ethernet Ring Protection Switching Solution

IGS-2700 and IPGS-2700 series industrial switches

IGS-2700 and IPGS-2700 Series Industrial L2+ Managed GbE Switches

Key Features

Benefits

Feature-rich Specifications to Support Various Applications

Exceptional Precision with IEEE 1588v2 PTP

Superior Reliability through OAM and CFM for Service Assurance

Easy to Install, Configure and Troubleshoot by Device Management System

Lowing Total Cost of Ownership (TCO) with Energy-efficient Design

Specifications

Surge 6KV Industrial grade Ethernet switches Solution

IGS-2724 and IPGS-2724 series industrial switches

IGS-2724 and IPGS-2724 SeriesIndustrial L2+ Managed GbE Switches

Key Features

Benefits

Feature-rich Specifications to Support Various Applications

Exceptional Precision with IEEE 1588v2 PTP

Superior Reliability through OAM and CFM for Service Assurance

Easy to Install, Configure and Troubleshoot by Device Management System

Lowing Total Cost of Ownership (TCO) with Energy-efficient Design

Specifications

IGS-2700 and IPGS-2700 Series
Industrial L2+ Managed GbE Switches

IGS-2724 and IPGS-2724 Series
Industrial L2+ Managed GbE Switches