OLT-E100
Product Overview
The Converter is designed to make conversion between 10/100/1000Base-T and EPON Optical Line Terminals (OLT) fiber Ethernet in the CO site conversion chassis. With web-based management and CLI (command line interface), the network administrator can logon the converter to monitor, configure and control the activity of each port. In addition, the EPON converter implements bandwidth rating management capability via the intelligent software. The overall network management is enhanced, and the network efficiency is also improved to accommodate and deliver high bandwidth applications.
Key Features
- Supports one 10/100/1000Base-T Gigabit Ethernet UTP port and one Gigabit Ethernet-PON Fiber port
- Supports Gigabit Ethernet-PON IEEE 802.3ah compliance
- Supports IEEE 802.3ah OAM function
- Supports 802.3z Gigabit Ethernet local-side interface
- Supports dynamic bandwidth allocation (DBA)
- Supports Supports 4K MAC address learning and aging on local interface
- Supports 802.1p with 4 priority queues per LLID link
- Supports Supports 802.1Q VLAN mapping to LLID
- Supports per-LLID/customer encryption and decryption for security
- Assurance of security for subscribers, Encryption in the PON layer assures security between subscribers
- Supports 256 LLIDs in each of downstream and upstream direction
- Supports local and remote loop-back test
- Supports statistics Rising/Falling threshold for alarm
- Supports configurable OLT alarm log function
- Supports RMON counters for port traffic quality monitoring function
- Supports IGMP proxy function
- Supports max packet length: 1536 bytes
- Supports module firmware upgrade
- Supports Module Information (S/N, MAC, Model Name,….)
- Supports module per port basic LEDs for monitoring
- Supports media type, connector, wavelength and distance information
- Supports hot-swap and auto reload configuration ability
- The center unit automatically scans and records ID information from subscriber systems
- RoHS Compliance
- Supports each converter module media configured and monitored ability:
| Supports port state enabled/disabled |
| Supports auto-negotiation/forced mode |
| Supports port speed and duplex mode |
| Supports flow control enabled/disabled |
- Supports wire speed packet forwarding ability as below：
| 10Base : 14880 pps |
| 100Base: 148800 pps |
| 1000Base: 1413600 pps |
(64Bytes up to 95% utilization)、(1518Bytes up to 97% utilization)
- Supports EPON module per port basic counters for traffic raw data monitor of fiber and TP port.
as below：
| Octets transferred |
| Total Frames transferred |
| Unicast Frames transferred |
| Broadcast Frames transferred |
| Multicast Frames transferred |
| CRC-32 Errors |
| Undersize Frames |
| Oversize Frames |
| Collisions |
| 64 Octet Frames |
| 65-127 Octet Frames |
| 128-255 Octet Frames |
| 256-511 Octet Frames |
| 512-1023 Octet Frames |
| 1024-1518 Octet Frames |
| 1519+ Octet Frames |
| Frames dropped (queue overflow) |
| Pause Frames |
Product Specification
| MODEL NAME | OLT-E100 |
|---|---|
| Product Description | 1-Port Gigabit Ethernet to EPON OLT Module |
LED Description
| LED | Color | Funciton |
|---|---|---|
| PWR | Green | Lit when power is coming up |
| EPON LNK | Green | Blink when EPON or LAN ports are disconnected Lit when PON and LAN ports are both linked |
| EPON ACT | Green | Lit when PON port is transmitting or receiving |
| LAN LNK/ACT | Green | Lit when LAN port is linked Blink when LAN port is transmitting or receiving |
| LAN SPD | Green/Yellow | Green lit when LAN port links on 1000Mbps speed Yellow lit when LAN port links on 100Mbps speed Off when LAN port unlinks |
Network Interface
Converter TP Port
100Base-TX:
– Auto-Negotiation
– Auto-MDIX
– flow control for Full-Duplex
– backpressure for Half-Duplex
1000Base-T:
– Auto-Negotiation Mode only
– Auto-MDIX only for Auto-Negotiation
– flow control for Full-Duplex only
Converter Fiber Port
OLT 1000Base-PX-U:
– Link partner must be ONU 1000Base-PX-U
TP Cable Limitations
Cat. 5 and up to 100m
Fiber Cable Limitations:
OLT 1000PX
– Single-Mode Fiber 9/125mm
– Single-Mode transceiver
– Output:1310nm 10 / 20Km
Note: Upstream=1310nm, Downstream=1490nm is the wavelength of EPON fiber transceiver
Standards:
IEEE802.3u 100Base-TX
IEEE802.3z/ab 1000Base-T
IEEE802.3ah 1000Base-PX-U (EPON)
UTP Cable:
Cat. 5 cable and up to 100m
Fiber Cable:
1000Base-PX-U
– 8.3/125mm Single-mode
– 8.7/125mm Single-mode
– 9/125mm Single-mode
– 10/125mm Single-mode
LED Indicators:
PWR
EPON LNK, ACT
TP LNK/ACT, SPD
Data Transfer Rate:
Upstream : Max. Up to 950 Mbps
Downstream : Max. Up to 970 Mbps
TP Interface (LAN):
100Base-TX
– NWay auto-negotiation
– Auto-MDIX
– Full/Half-Duplex
1000Base-T
– NWay auto-negotiation or force
– Auto-MDIX(only for Auto mode)
– Full-Duplex only
Fiber Interface :
1000Base-PX-U (EPON)
– Connector : SC/BiDi
– Max. Cable Length: 20Km for 9/125u
– Upstream (OLT RX)
– Wavelength : 1310nm
– Downstream (OLT TX)
– Wavelength : 1490nm
Power Requirement :
0.8A up @+12VDC
Power Consumption :
8.7 W
Ambient Temperature:
0° ~ 50°C
Humidity:
5% ~ 90%
Dimensions:
32.2(H) x 275(D) mm
Packing Information:
Carton Dimensions (mm) : 530x512x345
pcs/Carton : 30
N.W (KG) : 10.5
G.W (KG) : 11.5
Model
| Model | Dscription |
|---|---|
| OLT-E100BS4.S20 | 1-Port Gigabit Ethernet to EPON OLT Module, CO SC 20km, 1490nm |
Download
PDF Data sheet