■ Supports standard 9″ 1U high rackmount and wall-mount with 2-Port EPON OLT converter
■ Operating temp range: 0 ~ 50°C
■ Supports 2-Port GEPON OLT (Down stream: 2.5Gbps, Upstream:1.25Gbps)
■ Supports 2-Port GbE TP/SFP Combo (for uplink)
■ Built-in management CPU:
■ Supports RJ-45 RS232 interface for console
■ Supports one Out-of-Band (OOB) GbE RJ-45 port for management network
■ Support In-Band management from uplink interface
■ Supports DC-12V or AC 100~ 240V power input
■ Supports CO/CPE site local OLT and remote ONU configuration
■ Comply with RoHS Requirement
■ Provides 2-Port Gigabit Ethernet PON (Passive Optical Network), converting 10/100/1000 Mbps Ethernet into optical signals with an optical coupler for point-to-multipoint networks. The EPON OLT converter for the center unit can be selected to provide datacom service for distances of up to 20 km. The same subscriber unit EPON ONU converter is used for remote CPE site, whether 20 km type.
■ One OLT handles up to 32 subscribers per fiber
■ Implements full duplex with single SM fiber links, along with an optical coupler for 32 branches, making it possible to handle up to 32 subscribers per single optical fiber.
■ This OLT converter supports up to 64 subscribers

■ The converter has its own IP address, user name and password. In case of loss of username/password, a backdoor access will be available. It supports a forgetting username and password mechanism to login administrator right then reset the username and password.
■ Supports IEEE 802.3ah OAM function for CO and CPE site ” Remote Failure Indication” , “Remote Loopback” and”Link Monitoring”
■ Supports”Port Configuration” and “Bandwidth Configuration”
■ Remote monitoring and control functions
■ Remote control and monitoring via the SNMP protocol or a web browser, CLI control via TELNET is also supported.
■ Supports CO site media converter ingress/egress bandwidth rating management
■ Supports text-based text user interface with CLI via Telnet or RS-232 console serial interface
■ Supports CLI for multi-port CPE devices for port configuration, port counter, CO/CPE fiber link loop back test and link failure trap event log.
■ Supports Web UI for multi-port CPE devices for port configuration, port counter, CO/CPE fiber link loop back test and link failure trap event log.
■ Supports Neutral web-based graphic user interface
■ Supports MIB II, Enterprise MIB and SNMP Traps with SNMPv1, v2c and v3
■ Supports SNMP MIB OID for multi-port CPE devices for port configuration, port counter, CO/CPE fiber link loopback test and link failure trap event.
■ Supports RMON 1,2,3,9 groups (for CO site module’s port)
■ Supports Management Security Configuration. It can filter connections by IP range, connection type – http, telnet and SNMP and filter action – accept or deny.
■ Supports network time sync function with NTP and daylight savings
■ Supports domain name address instead of IP address for NTP server and E-mail server setting
■ Supports device name and location configurable function
■ Supports SNMP access filtering for security, the SNMP set function could be disabled to limit the configurations be changed via SNMP set function
■ Supports up to 6 trap / alarm hosts to receive the trap host and alarm message via mail and short message receiver
■ Support IPv4 and IPv6 dual stack for management
■ Supports DHCP client for dynamic IP assignment
■ Supports user account management, there are two level user authority
■ Administrator User: Only one user is administrator authority in the chassis. The user could modify and look all confiqurations
■ Guest User: The chassis could be set up to four guest authority users, the users could look configuration only, could not change confiqurations
■ Supports Syslog to backup the trap log data.
■ Supports firmware upgrade, configuration data import/export and log data export via TFTP
■ Supports diagnostic ping for the chassis to test an alive network device IP, the testing result included response time, nr. of packets and ping success rate.
■ Supports auto logout, user can adjust the Auto-Logout time in nSupports import / export configuration file in Web UI, CLI and SNMP function via TFTP protocol to backup and restore configuration
■ Simpler system configuration at installation
■ The center unit automatically scans and records ID information from subscriber systems.
■ Assurance of security for subscribers
■ Encryption in the PON layer assures security betwee

2-Port EPON OLT Media converter

SNMP and web-base via in-band LAN port or local serial CLI
― AC: 100-240VAC, 50-60Hz
― DC: 12V