PSGC-110A

10/100/1000Base-T to SFP PoE PSE GbE Media Converter
PSGC-110A is designed a 10/100/1000Base-T to 1000Based-SX/LX (SC/LC) GbE media converter, which allows two types of network segments to be connected easily and inexpensively. Complied with IEEE802.3af Power Over Ethernet standard, this AC powered PoE media converter is a Power Sourcing Equipment (PSE) which combines data received over a TP link with –48VDC power, providing power to IEEE802.3af powered device (PD) over the existing CAT5 UTP cable. The converter includes a PD signature sensing and power monitoring features. Other features include over-current protection, under-current detection and fault protection input. The LFP (Link Fault Pass-through) allows the media converter to monitor both the fiber and copper RX ports for loss of signal. In case of a loss of RX signal on one media port, the converter will automatically disable the TX signal to the other media port, thus passing through the link fault. FEF (Far End Fault) enables the converter to stop sending link pulse to the link partner once a loss of the fiber RX signal is encountered. Then the link partner will synchronously stop sending data. FEF prevents loss of valuable data transmitted over invalid link. Combining LFP and FEF troubleshooting features of PSGC-110A, both end devices can be notified of a loss of fiber link.
Key Features
- IEEE802.3af PoE (Power over Ethernet) PSE compatible
― Internal AC power supply
― Over-current protection
― Under-current detection
― Minimum load sensing
― Fault Protection Input
― PSE MDI power enable/disable - LFP (Link Fault Pass-through) and FEF (Far End Fault)
- Supports one 10/100/1000Base-T Gigabit Ethernet UTP port and one 1000Base-SX / LX (SFP) Gigabit Ethernet Fiber port
- Supports 802.3x flow control for full-duplex ports and backpressure for half-duplex ports
- Supports comprehensive types of fiber with different distances and connections, including Bidi/LC and so on
- Supports auto mode on the TP port
- DIP switch to set configurations
― DIP 1: LFP/LFP DIS
― DIP 2: PoE/PoE DIS
― DIP 3: Bridge Mode/Cut Through Mode - Supports jumbo frame (Normal Mode: 2KB, Cut-Through Mode: 9KB)
- RoHS Compliance
- IEEE802.3af PoE (Power over Ethernet) PSE compatible
― Internal AC power supply
― Over-current protection
― Under-current detection
― Minimum load sensing
― Fault Protection Input
― PSE MDI power enable/disable - LFP (Link Fault Pass-through) and FEF (Far End Fault)
- Supports one 10/100/1000Base-T Gigabit Ethernet UTP port and one 1000Base-SX / LX (SFP) Gigabit Ethernet Fiber port
- Supports 802.3x flow control for full-duplex ports and backpressure for half-duplex ports
- Supports comprehensive types of fiber with different distances and connections, including Bidi/LC and so on
- Supports auto mode on the TP port
- DIP switch to set configurations
― DIP 1: LFP/LFP DIS
― DIP 2: PoE/PoE DIS
― DIP 3: Bridge Mode/Cut Through Mode - Supports jumbo frame (Normal Mode: 2KB, Cut-Through Mode: 9KB)
- RoHS Compliance
Specifications
Standards
IEEE802.3 10Base-T,
IEEE802.3u 110ase-TX,
IEEE802.3z/ab 1000Base-T,
IEEE802.3x full-duplex flow control,
1000Base-SX/LX
Cable
UTP:Cat. 5 cable and up to 100m
Fiber:
―1000SX:50/125, 62.5/125, or 100/140μm multi-mode
―1000LX:8.3/125, 8.7/125, 9/125 or 10/125μm single-mode
Cable Connection Parameter
TP Cable Limitations:Cat. 5 and up to 100m
Fiber Cable Limitations:
Multi-Mode Fiber 62.5/125μm | Multi-Mode Fiber 50/125μm | |||
Bandwidth MHz-Km | Distance | Bandwidth MHz-Km | Distance | |
1000SX 850nm | 160 | 220m | 400 | 500m |
200 | 275m | 500 | 550m | |
1000LX 1310nm/1550nm | Single-Mode Fiber 9/125μm Single-Mode transceiver 1310nm: 10/30Km Single-Mode transceiver 1550nm: 50Km |
Data Transfer Rate
2000Mbps/full-duplex
Network Interface
TP Port | 10/100Base-TX Auto-Negotiation Auto-MDIX Flow control for Full-Duplex Backpressure for Half-Duplex |
TP Port | 1000Base-TX Auto-Negotiation mode Auto-MDIX only for Auto-Negotiation Flow control for Full-Duplex only |
Fiber Port | 1000Base-SX/LX (SFP) with NWay flow control Link partner must be 1000FDX with NWay flow control |
LED Indicator
LED | Color | Function |
---|---|---|
FX LNK/ACT | Green | Lit when fiber connection is good Blinks when fiber data is present |
TP LNK/ACT | Green | Lit when TP connection is good Blinks when TP data is present |
TP SPD | Green Yellow | Green Lit when TP speed is 1000Mbps Yellow Lit when TP speed is 100Mbps Off when TP speed is 10Mbps |
PWR | Green | Lit when +5V power is coming up |
PoE PSE-TP | Green | Lit when PoE feeding power is active |
Red | Lit when PoE feeding power is disrupted (In case of overtemperature/overcurrent) | |
4W | Green | Light when PD Class Type is Class 1 |
7W | Green | Light when PD Class Type is Class 2 |
15.4W | Green | Light when PD Class Type is Class 0 or 3 |
Hardware Spec
Feature | Detailed Description |
---|---|
Power Characteristics | Requirement :100 – 240 VAC, 47 –63 Hz Consumption :Max. up to 19W |
Ambient Temperature | 0 ~ 50°C |
Humidity | 5 ~ 90% |
Dimensions | 40(H) x 158(W) x 133(D) mm |
Weight | 0.6kg |
EMI | Comply with FCC Part 15 Class A & CE Mark Approval |
Packing Information
Carton Dimensions(mm) | pcs/Carton | N.W (KG) | G.W (KG) |
---|---|---|---|
530x512x345 | 14 | 16.4 | 17.4 |
Ordering Information
PSGC-110ALC | 10/100/1000Base-T to SFP PoE PSE GbE Media Converter, LC Multi-Mode, 850nm |
PSGC-110ALC.S10 | 10/100/1000Base-T to SFP PoE PSE GbE Media Converter, LC Single-Mode 10km 1310nm |
PSGC-110ALC.S30 | 10/100/1000Base-T to SFP PoE PSE GbE Media Converter, LC Single-Mode 30km 1310nm |
PSGC-110ALC.S50 | 10/100/1000Base-T to SFP PoE PSE GbE Media Converter, LC Single-Mode 50km 1550nm |
PSGC-110ABL3.S10 | 10/100/1000Base-T to SFP PoE PSE GbE Media Converter, Bidi LC Single-Mode 10km, 1310nm |
PSGC-110ABL5.S10 | 10/100/1000Base-T to SFP PoE PSE GbE Media Converter, Bidi LC Single-Mode 10km, 1550nm |
PSGC-110ABL3.S20 | 10/100/1000Base-T to SFP PoE PSE GbE Media Converter, Bidi LC Single-Mode 20km, 1310nm |
PSGC-110ABL5.S20 | 10/100/1000Base-T to SFP PoE PSE GbE Media Converter, Bidi LC Single-Mode 20km, 1550nm |
Download
PDF Data sheet
- + Datasheet
-
10/100/1000Base-T to SFP PoE PSE GbE Media Converter
PSGC-110A is designed a 10/100/1000Base-T to 1000Based-SX/LX (SC/LC) GbE media converter, which allows two types of network segments to be connected easily and inexpensively. Complied with IEEE802.3af Power Over Ethernet standard, this AC powered PoE media converter is a Power Sourcing Equipment (PSE) which combines data received over a TP link with –48VDC power, providing power to IEEE802.3af powered device (PD) over the existing CAT5 UTP cable. The converter includes a PD signature sensing and power monitoring features. Other features include over-current protection, under-current detection and fault protection input. The LFP (Link Fault Pass-through) allows the media converter to monitor both the fiber and copper RX ports for loss of signal. In case of a loss of RX signal on one media port, the converter will automatically disable the TX signal to the other media port, thus passing through the link fault. FEF (Far End Fault) enables the converter to stop sending link pulse to the link partner once a loss of the fiber RX signal is encountered. Then the link partner will synchronously stop sending data. FEF prevents loss of valuable data transmitted over invalid link. Combining LFP and FEF troubleshooting features of PSGC-110A, both end devices can be notified of a loss of fiber link.
Key Features
- IEEE802.3af PoE (Power over Ethernet) PSE compatible
― Internal AC power supply
― Over-current protection
― Under-current detection
― Minimum load sensing
― Fault Protection Input
― PSE MDI power enable/disable - LFP (Link Fault Pass-through) and FEF (Far End Fault)
- Supports one 10/100/1000Base-T Gigabit Ethernet UTP port and one 1000Base-SX / LX (SFP) Gigabit Ethernet Fiber port
- Supports 802.3x flow control for full-duplex ports and backpressure for half-duplex ports
- Supports comprehensive types of fiber with different distances and connections, including Bidi/LC and so on
- Supports auto mode on the TP port
- DIP switch to set configurations
― DIP 1: LFP/LFP DIS
― DIP 2: PoE/PoE DIS
― DIP 3: Bridge Mode/Cut Through Mode - Supports jumbo frame (Normal Mode: 2KB, Cut-Through Mode: 9KB)
- RoHS Compliance
- IEEE802.3af PoE (Power over Ethernet) PSE compatible
― Internal AC power supply
― Over-current protection
― Under-current detection
― Minimum load sensing
― Fault Protection Input
― PSE MDI power enable/disable - LFP (Link Fault Pass-through) and FEF (Far End Fault)
- Supports one 10/100/1000Base-T Gigabit Ethernet UTP port and one 1000Base-SX / LX (SFP) Gigabit Ethernet Fiber port
- Supports 802.3x flow control for full-duplex ports and backpressure for half-duplex ports
- Supports comprehensive types of fiber with different distances and connections, including Bidi/LC and so on
- Supports auto mode on the TP port
- DIP switch to set configurations
― DIP 1: LFP/LFP DIS
― DIP 2: PoE/PoE DIS
― DIP 3: Bridge Mode/Cut Through Mode - Supports jumbo frame (Normal Mode: 2KB, Cut-Through Mode: 9KB)
- RoHS Compliance
Specifications
Standards
IEEE802.3 10Base-T,
IEEE802.3u 110ase-TX,
IEEE802.3z/ab 1000Base-T,
IEEE802.3x full-duplex flow control,
1000Base-SX/LXCable
UTP:Cat. 5 cable and up to 100m
Fiber:
―1000SX:50/125, 62.5/125, or 100/140μm multi-mode
―1000LX:8.3/125, 8.7/125, 9/125 or 10/125μm single-modeCable Connection Parameter
TP Cable Limitations:Cat. 5 and up to 100m
Fiber Cable Limitations:Multi-Mode Fiber
62.5/125μmMulti-Mode Fiber
50/125μmBandwidth
MHz-KmDistance Bandwidth
MHz-KmDistance 1000SX
850nm160 220m 400 500m 200 275m 500 550m 1000LX
1310nm/1550nmSingle-Mode Fiber 9/125μm
Single-Mode transceiver 1310nm: 10/30Km
Single-Mode transceiver 1550nm: 50KmData Transfer Rate
2000Mbps/full-duplex
Network Interface
TP Port 10/100Base-TX
Auto-Negotiation
Auto-MDIX
Flow control for Full-Duplex
Backpressure for Half-DuplexTP Port 1000Base-TX
Auto-Negotiation mode
Auto-MDIX only for Auto-Negotiation
Flow control for Full-Duplex onlyFiber Port 1000Base-SX/LX (SFP)
with NWay flow control
Link partner must be 1000FDX with NWay flow controlLED Indicator
LED Color Function FX LNK/ACT Green Lit when fiber connection is good
Blinks when fiber data is presentTP LNK/ACT Green Lit when TP connection is good
Blinks when TP data is presentTP SPD Green
YellowGreen Lit when TP speed is 1000Mbps
Yellow Lit when TP speed is 100Mbps
Off when TP speed is 10MbpsPWR Green Lit when +5V power is coming up PoE PSE-TP Green Lit when PoE feeding power is active Red Lit when PoE feeding power is disrupted
(In case of overtemperature/overcurrent)4W Green Light when PD Class Type is Class 1 7W Green Light when PD Class Type is Class 2 15.4W Green Light when PD Class Type is Class 0 or 3 Hardware Spec
Feature Detailed Description Power Characteristics Requirement :100 – 240 VAC, 47 –63 Hz
Consumption :Max. up to 19WAmbient Temperature 0 ~ 50°C Humidity 5 ~ 90% Dimensions 40(H) x 158(W) x 133(D) mm Weight 0.6kg EMI Comply with FCC Part 15 Class A & CE Mark Approval Packing Information
Carton Dimensions(mm) pcs/Carton N.W (KG) G.W (KG) 530x512x345 14 16.4 17.4 Ordering Information
PSGC-110ALC 10/100/1000Base-T to SFP PoE PSE GbE Media Converter, LC Multi-Mode, 850nm PSGC-110ALC.S10 10/100/1000Base-T to SFP PoE PSE GbE Media Converter, LC Single-Mode 10km 1310nm PSGC-110ALC.S30 10/100/1000Base-T to SFP PoE PSE GbE Media Converter, LC Single-Mode 30km 1310nm PSGC-110ALC.S50 10/100/1000Base-T to SFP PoE PSE GbE Media Converter, LC Single-Mode 50km 1550nm PSGC-110ABL3.S10 10/100/1000Base-T to SFP PoE PSE GbE Media Converter, Bidi LC Single-Mode 10km, 1310nm PSGC-110ABL5.S10 10/100/1000Base-T to SFP PoE PSE GbE Media Converter, Bidi LC Single-Mode 10km, 1550nm PSGC-110ABL3.S20 10/100/1000Base-T to SFP PoE PSE GbE Media Converter, Bidi LC Single-Mode 20km, 1310nm PSGC-110ABL5.S20 10/100/1000Base-T to SFP PoE PSE GbE Media Converter, Bidi LC Single-Mode 20km, 1550nm - IEEE802.3af PoE (Power over Ethernet) PSE compatible
- + Download
-
Download
PDF Data sheet